use for quoting, preliminary design, prototyping and informational purposes only not released for production 28.00 0.10 29.31 26.63 14.00 4.50 3.24 (typ) 8.87 0.10 m 1.60 x 0.35 thru (2 plcs) c l see note 2 -x- 0.10 -y- r 2.30 (4 plcs) true r 1.30 (8 plcs) 8.000 "a" "a" c l c l 13.62 14.82 32.49 r 1.50 (typ) 6.0 (typ) 0.70 (2 plcs) 5 "b" "b" 0.10 -z- -w- 18.12 11.25 13.87 8.50 26.91 26.00 r 1.00 (typ) 24.75 3.00 (2 plcs) 9.874 2.400 (2 plcs) m1.6 x 0.35 3.80 (2 plcs) r 0.50 (typ) (2 plcs) m1.6 x 0.35 4.50 c l c1 c2 0.10 w x y 0.10 w x y c sheet of unless otherwise specified, dimensions are in millimeters. tolerances are: decimals angles x.x: 0.3 2 x.xx: 0.13 x.xxx: 0.025 0.635mm edge mount pcb cage by: ASP-149118-01 dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing vicky z 12/09/2009 2 1 sheet scale: 2:1 ASP-149118-01 f:\dwg\sw\newprod\pt635mm\hypertransport\ASP-149118-01.slddrw plating: cu: 0.008 - 0.015 mm [.0003 - .0006 in.] underplate ni: 0.003 - 0.008 mm [.0001 - .0003 in.] revision notes: 1. represents a critical dimension. 2. samtec shall appear on surface shown, approximately 3. all identification marks must not stand greater than 0.05 off the surface of the part. 4. molded surfaces shall be consistent and smooth. surfaces to be free of scratches, nicks, sink areas, voids or other blemishes. 5. parts to be packaged in trays. 6. all draft must be within tolerances. 7. parts to be shot blasted. 8. dimension to be adjustable in the die. 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322 material: zamak 3 max gate vestige: 0.13 max flash allowed: 0.08
1.75 (typ) 6.631 3.483 1.00 (typ) 1.95 (typ) 'c' section "a"-"a" 9.874 ref 4.85 0.05 (typ) 5.75 0.05 (typ) detail 'c' scale 4 : 1 c5 c6 0.10 z 0.10 z 26.70 30 1.54 1.000 28.00 ref 25.83 0.05 'd' 'e' section "b"-"b" c3 c4 0.10 x z 0.10 x -x- 0.10 x 1.55 1.50 2.35 0.05 (see note 8) 0.20 45 (typ) 20 0.39 2.00 r 0.40 (typ) detail 'd' scale 8 : 1 c7 0.09 ref 25.83 ref detail 'e' scale 8 : 1 sheet of 0.635mm edge mount pcb cage by: ASP-149118-01 dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. vicky z 12/09/2009 2 2 sheet scale: 2:1 f:\dwg\sw\newprod\pt635mm\hypertransport\ASP-149118-01.slddrw revision 0 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
|